on video A miniature DC 3.6~24V Wireless RF Remote Control Switch,with Momentary、Toggle、Latching、Delay Modes

This is a miniature DC 3.6~24V Wireless RF Remote Control Switch,which can be used for Christmas tree light string, stage scene lighting and DIY.


It has the characteristics of simple wiring, easy pairing, sensitive control, low power consumption, strong wearability,wall penetration, and anti-interference.

Here are some basic parameters：
Working voltage: DC 3.6~24V（output as much as input）
Maximum load: 2A
Function Modes:Momentary、Toggle、Latching、Delay（5s ~ 20s）
Remote control distance: 30 meters (up to 50 meters in an open environment)

About working modes:
Momentary Mode:Press and hold the remote button , the relay connects; release the remote button , the relay disconnects.
Toggle Mode:Press once the remote button , the relay connects ;press the button again the relay disconnects.
Latching Mode:Press the remote button A, the relay connects; press the remote button B, the relay disconnects.
Delay Mode:Press the remote control button , the relay connects ; after 5s or 10s or 15s or 20s , the relay disconnect automatically.

RECEIVER OPERATING MODE SETTINGS

Momentary Mode Setting

Press the learning button of the receiver once , it comes into Momentary setting mode.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote button,the LED indicator will flash 3 times and then go out, the setting is successful.

Toggle Mode Setting

Press the learning button of the receiver twice, it comes into Toggle setting mode.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote button,the LED indicator will flash 3 times and then go out, the setting is successful.

Latching Mode Setting

When selecting the Latching Mode, two different buttons need to be set, the first button is set to "ON", and the second button is set to "OFF".
Press the learning button of the receiver 3 times,it comes into Latching setting mode.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote control button “ON”, the LED indicator flashes 3 times.
Press the remote control button “OFF”, the LED indicator flashes 3 times and then goes out, the setting is successful.

Delay Mode Setting

Press the learning button of the receiver 4 times, with a delay of 5 seconds.
Press the learning button of the receiver 5 times, with a delay of 10 seconds.
Press the learning button of the receiver 6 times, with a delay of 15 seconds.
Press the learning button of the receiver 7 times, with a delay of 20 seconds.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote button,the LED indicator will flash 3 times and then go out, the setting is successful.

Automatic energize when power on

Press and hold the learning button until the led indicator light flashes, the setting is complete.

How to reset

Press the learning button of the receiver 8 times, the receiver will clear all remote control data in the memory.
After the receiver resets the data, the remote control needs to be re-paired with the receiver to control the receiver.
 

This is a miniature DC 3.6~24V Wireless RF Remote Control Switch,which can be used for Christmas tree light string, stage scene lighting and DIY.


It has the characteristics of simple wiring, easy pairing, sensitive control, low power consumption, strong wearability,wall penetration, and anti-interference.

Here are some basic parameters：
Working voltage: DC 3.6~24V（output as much as input）
Maximum load: 2A
Function Modes:Momentary、Toggle、Latching、Delay（5s ~ 20s）
Remote control distance: 30 meters (up to 50 meters in an open environment)

About working modes:
Momentary Mode:Press and hold the remote button , the relay connects; release the remote button , the relay disconnects.
Toggle Mode:Press once the remote button , the relay connects ;press the button again the relay disconnects.
Latching Mode:Press the remote button A, the relay connects; press the remote button B, the relay disconnects.
Delay Mode:Press the remote control button , the relay connects ; after 5s or 10s or 15s or 20s , the relay disconnect automatically.

RECEIVER OPERATING MODE SETTINGS

Momentary Mode Setting

Press the learning button of the receiver once , it comes into Momentary setting mode.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote button,the LED indicator will flash 3 times and then go out, the setting is successful.

Toggle Mode Setting

Press the learning button of the receiver twice, it comes into Toggle setting mode.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote button,the LED indicator will flash 3 times and then go out, the setting is successful.

Latching Mode Setting

When selecting the Latching Mode, two different buttons need to be set, the first button is set to "ON", and the second button is set to "OFF".
Press the learning button of the receiver 3 times,it comes into Latching setting mode.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote control button “ON”, the LED indicator flashes 3 times.
Press the remote control button “OFF”, the LED indicator flashes 3 times and then goes out, the setting is successful.

Delay Mode Setting

Press the learning button of the receiver 4 times, with a delay of 5 seconds.
Press the learning button of the receiver 5 times, with a delay of 10 seconds.
Press the learning button of the receiver 6 times, with a delay of 15 seconds.
Press the learning button of the receiver 7 times, with a delay of 20 seconds.
Wait for a moment, the LED indicator of the receiver board will be on.
Press the remote button,the LED indicator will flash 3 times and then go out, the setting is successful.

Automatic energize when power on

Press and hold the learning button until the led indicator light flashes, the setting is complete.

How to reset

Press the learning button of the receiver 8 times, the receiver will clear all remote control data in the memory.
After the receiver resets the data, the remote control needs to be re-paired with the receiver to control the receiver.